Half shaft introduce

Driver Shaft, also known as CVJ, CV joint, constant velocity joint, is a shaft that transmits torque between the gearbox reducer and the drive wheel. It has a U-joint at the inner and outer ends, which is connected to the reducer gear and the inner ring of the hub bearing through splines on the U-joint [2] The half shaft is the shaft that transfers torque between the gearbox reducer and the drive wheel (previously mostly solid, but due to the uneven rotation control of the hollow shaft, many cars use hollow shafts). It has a universal joint (U/JOIN) at the inner and outer ends, which is connected to the reducer gear and the inner ring of the hub bearing through splines on the universal joint. There are two types of half shafts commonly used in modern cars, full floating and semi floating, depending on their support types (There are also three types, namely fully floating. 3/4 floating and semi floating.) The fully floating half axle only transmits torque and does not withstand any reaction force or bending moment. When combined with independent suspension, it is beneficial to improve vehicle comfort and is widely used in various types of cars. The fully floating half axle is easy to disassemble, and during maintenance and repair, the half axle can be removed by simply unscrewing the fixing bolts of the half axle, while the wheels and axle housing can still support the car, Thus, it brings convenience to car maintenance. The semi floating half axle not only transmits torque but also bears all reaction forces and bending moments. Its supporting structure is simple and low in cost, mainly suitable for pickup trucks and SUVs that do not require high comfort requirements. However, this type of half axle support is difficult to remove, and if the half axle breaks during driving, it is easy to cause the risk of wheels flying off, which is a form that is about to be phased out)

Steps for disassembling and installing the rear axle half shaft of a car

The steps for disassembling and assembling the rear axle half shaft of a car are as follows: 1. Lift the car and support it reliably. Remove the rear suspension swing arm bolts; 2. Remove the fixing bolts and covers of the outer cross shaft universal joint, and remove the fixing bolts and covers of the inner cross shaft universal joint; 3. Slide the half shafts together, do not apply too much force, remove the half shafts, do not let them hang vertically, to prevent damage to the universal joint bearings caused by impact; 4. Check if the universal joint assembly is worn or damaged, and if necessary, replace the universal joint; 5. When installing the rear axle half shaft, first install the half shaft onto the inner universal joint. The diameter of the inner half shaft is larger than that of the outer half shaft. Install the universal joint fixing cover and fixing bolts, and tighten the bolts with the corresponding torque. Note: Make sure to use Loctite glue on the universal joint fixing bolts; 6. Install the half shaft onto the outer universal joint, install the universal joint fixing cover and fixing bolts, and tighten the bolts with the corresponding torque; 7. Install the rear suspension swing arm and tighten the bolts to the corresponding torque

BEIJING-U7 introduce

The super practical storage space of Beijing Automotive Beijing-U7 (formerly known as Beijing Automotive Zhidao U7) has reduced a lot of trouble for travel. The most pleasing aspect of the front storage space is its central armrest box. The two-piece design supports left and right split opening. This design is generally only found in high-end models of Mercedes Benz and BMW, and it is not easy to make the armrest box so innovative at this price point, The space design of this central armrest box is also excellent, with a large depth and strong practicality. In addition, there are two central cup holders in front of the central armrest box, which are just right for storing mineral water. The largest storage compartment in the central control area is located in the area in front of the gear lever, and there are also two USB ports and a 12V power supply. In addition, there is a small storage compartment on the left side of the driver's side, It can be used to store change, bills, and other miscellaneous items. The storage space inside the front glove box and door panel is also large, and the interior of the glove box is treated with flocking, so it is not afraid of scratching valuable items