Rear wheel fender introduce

The leaf plate includes: front leaf plate, front leaf plate lining, front leaf plate light, rear leaf plate light, radiator frame. The leaf plate refers to a type of cover on motor vehicles and non motor vehicles (a slightly protruding, semi-circular small piece above the wheel), and the cover, as the name suggests, is the shell that covers the outside of motor vehicles and non motor vehicles. It conforms to fluid mechanics and reduces the wind resistance coefficient, Make the car run more smoothly. The fender, also known as the fender, is located outside the body of the wheels. Its function is to reduce the drag coefficient of the fender air outlet according to fluid dynamics, making the car run more smoothly. According to the installation position, it is divided into front fender and rear fender. The front fender is installed above the front wheel, because the front wheel has steering function, it is necessary to ensure the maximum limit space when the front wheel rotates, Therefore, designers will use a "wheel runout chart" to verify the design dimensions of the fender based on the selected tire model size. The rear fender does not have the problem of wheel rotation collision, but due to aerodynamic considerations, the rear fender slightly arches outward. Secondly, the front fender can prevent sand, stones, and mud rolled up by the wheels from splashing onto the bottom of the car during driving, reducing damage and corrosion to the chassis, The materials used are required to have weather aging resistance and good formability. Currently, many car front fenders are made of plastic materials with a certain degree of elasticity, making them more cushioning and safer)

Installation method of rear fender/rear fender assembly

1. Start the car and turn all wheels to the right, then turn off the engine and remove the car key. Then open the engine hood and disconnect the negative pole of the battery. Use a Phillips screwdriver to remove the four screws on the front bumper. Use a 5mm hex wrench to remove the two screws on the side of the front bumper; 2. Use a Phillips screwdriver and a 7mm socket to remove the three screws under the right side of the front bumper fascia. Use a Phillips screwdriver and a 7mm socket to remove the three screws of the fender. Remove the splash guard; 3. Use a small ratchet wrench, extension rod, and 7mm socket to remove the screws at the bottom of the front bumper. Use a square screwdriver and 7mm socket to remove the screws connecting the fender and bumper. Use a large ratchet wrench and 10mm socket to remove the four bolts behind the front headlight; 4. Remove the plug of the front headlight assembly. Remove the front headlight assembly. Remove the screws connecting the splash guard to the fender, and the fender can be removed; 5. The fender is located outside the vehicle body of the wheels. Its function is to reduce the drag coefficient based on fluid dynamics, making the vehicle travel smoother. It is further divided into front fender and rear fender according to the installation position, with the front fender installed above the front wheel; 6. Due to the steering function of the front wheels, it is necessary to ensure the maximum limit space when the front wheels rotate. Therefore, the designer will use the "wheel runout diagram" based on the selected tire model size to verify the design size of the fender

corolla introduce

The Corolla is the tenth generation straight upgrade product of Toyota COROLLA. Since its release in November last year, the Corolla has received global consumer attention; Now, this globally popular car has settled in FAW Toyota, once again allowing Chinese consumers to experience Toyota's latest technology and driving experience simultaneously. The predecessor of the Corolla was the AE86! The size of the Corolla body has significantly increased compared to the previous generation Corolla, and the entire vehicle has shown an unprecedented "wide and low" trend, creating a spacious interior space; The newly developed dual VVT-i technology with 1.6-liter and 1.8-liter engines will bring a more powerful power experience in the future The Corolla, the tenth generation Corolla that has been officially released in China and has become the focus of attention at the Beijing and Shanghai Auto Show, is the latest model in its series. It was officially launched on November 16, 2006. The Corolla, which is about to be launched by FAW Toyota, has two displacement models: 1.6L and 1.8L. Whether in terms of appearance, configuration, or power, the Corolla, The Corolla has been greatly improved on the basis of the old Corolla. The average fuel consumption of the Corolla is 8.88L/100km, and car owners have expressed that its fuel consumption is low. According to feedback from car owners in 2012, the Corolla has almost no problem with any malfunctions and its quality is very stable. Car owners generally recognize the Corolla in terms of acceleration and handling, Compared to the old Corolla, there has been a significant improvement. However, the 4-speed automatic transmission is slightly stingy. Car owners generally report that the fastest acceleration is achieved from 2nd to 3rd gear