safety belt introduce

"Safety" has become the primary concern for drivers and passengers, and is also one of the most important performance factors for cars. Traditional components that ensure safe driving, such as rearview mirrors and left and right door mirrors (traditional rearview systems), seat belts, AIRBAGs (airbags), and ABS (anti lock braking systems), have been widely used by drivers and passengers, and are widely used in imported luxury cars. However, Traditional concepts of safe driving: safety belts, AIRBAG ABS, and traditional rearview systems do not equal the entire concept of safety, as traditional rearview systems consist of three flat or wide-angle mirrors with blind spots (dead angles) and parallax, Blind spots and parallax are often the causes of car accidents. Car seat belts are devices used in cars to prevent passengers and drivers from being injured by airbags when the body of the car is hit hard. To ensure the correct positioning of the belt, tie the lap part of the waist belt under the pelvis, and hang the shoulder belt diagonally in front of the chest, Cannot be fastened to other parts. A seat belt can only be used by one person. The seat belt cannot be twisted up for use. Wearing thick clothing may cause the seat belt to be in an incorrect position. Do not let the seat belt rub against sharp edges. Do not tilt the seat back too much, otherwise the seat belt cannot be properly extended or shortened. Do not press the seat belt onto hard or fragile objects, If the seat belt has been subjected to a severe impact, even if it is not damaged, the assembly should be replaced. The seat belt should be regularly checked for wear and damaged parts should be replaced. When there is no one on the seat, the seat belt should be fully retracted into the retracter so that the buckle is in the storage position, avoiding emergency braking, Buckle tongue collides with an object. The seat belt can be cleaned with soft soap and water with a cloth or sponge. Do not use dyes and bleach on the seat belt, as it will reduce its strength)

Introduction to good installation methods for seat belts

Introduction to good installation methods for seat belts: Process 1. Sitting on a car seat, pull out the seat belt with one hand and hold the buckle with the other hand, using the buckle to secure the buckle to ensure that the seat belt is securely fastened to the body. 2. Adjust the belt position. The three-point waist belt should be tied as low as possible, tied to the hips, not to the waist. 3. Adjust the position of the shoulder belt. The shoulder belt should be comfortably hung at the collarbone, rather than pinching the neck or rubbing against the face, It's not necessary to hang it under your arm. 4. Check if the seat belt is secure before driving to ensure its proper performance before driving. 5. Unfasten your seat belt. Hold the buckle with one hand and press

Chrysler 300M introduce

Basic parameters: Manufacturer Chrysler brand Chrysler model (style) 2002 Chrysler 300M production time (year) 2002 Drive form Front wheel drive fuel consumption (L/100km) 10 Main dimensions and mass: Length/width/height (mm) 5024/1890/1422 wheelbase (mm) 2870 wheelbase (front and rear) (mm) 1574/1564 Rear trunk volume (L) 530 Fuel tank volume (L) 64 curb weight (kg) 1629 engine parameters: engine position front engine, longitudinally placed engine type V6 60 degree angle DOHC 24V cylinder number 6 cylinder diameter/stroke (mmXmm) 96.00 × 81.00 displacement (mL) 3518 compression ratio 9.90:1 ignition mode SMPFi maximum power (kw) 253.5PS (186.4 kW)/6400rpm maximum torque (N.m) 339.0Nm (34.6 kgm)/3900rpm chassis parameters: transmission type 4A suspension (front/rear) front lateral swing arm, elastic strut, stabilizer bar rear multi steering shaft, elastic strut, Lateral stabilizer bar braking device type (front/rear)) front and rear ventilated disc with ABS tire type and specifications (km/h) Michelin Energy MXV4 Plus P225/55 R 17 Body parameters: number of doors 4 seats 4/5 drag coefficient 0.313 minimum turning diameter 11.50 Other: domestic reference price (RMB 10000) 46 international reference price (USD 10000) 2.91