Front turn signal introduce

Turn signal is an important indicator light that is activated when a motor vehicle turns to remind the front, rear, left, right, and pedestrians to pay attention. The turn signal tube uses xenon gas tubes, a microcontroller control circuit, and the left and right rotate continuously to flash. The turn signal uses a flasher to achieve light flashing. It can be mainly divided into three types: wire blocking, capacitive, and electronic. Among them, wire blocking can be further divided into hot wire (electric heating) and wing type (bouncing), Electronic flashers can be divided into hybrid (with contact relays and electronic components) and fully electronic (without relays). For example, pop-up flashers use the principle of electric current thermal effect, which uses thermal expansion and contraction as power to cause sudden changes in the spring plate to connect and disconnect the contacts, achieving flashing lights. Turn signals are the most important device that represents the dynamic information of the car, installed in front and behind the body, and can be turned on when the car turns, providing safety assurance for driving, For your and others' safety, please use turn signals according to regulations, so that people can know the direction of the car in advance and make correct judgments)

Installation of front turn signals/rear turn signals/LED daytime running lights/side marker lights/front and rear position lights

Tool preparation: 1. First, we need to prepare the tools required for the entire process of installing car turn signals, including a screwdriver and a wire hook. Then, we need to prepare the car turn signals that need to be installed. 2. Turn on the double flash. As shown in the figure, open the car's key door, and press the switch button of the double flash by hand. This way, the car's double flash will open. Observe the position of the turn signal wire harness. Now we can take out the iron hook, You can make this iron hook yourself, just put it on a wire head. It's quite simple because we have a dual flash, so we can observe the position of the turn signal harness through the hole. 3. Hook out the turn signal. As shown in the figure, after we find the position of the turn signal harness, we use the small iron hook made to hook the harness, and then hook out the turn signal. Be careful to hook it slowly, Avoid disconnecting the wiring harness, and also be careful not to scratch the surface of the car, which may affect its appearance. For the first time installing a car turn signal, as shown in the figure, take out the car turn signal that needs to be installed. Let's take a closer look. There are two small snap holes on the turn signal lampshade that can be directly attached to the turn signal. Please find a good position and gently attach the turn signal to the lampshade. 4. Installation of the car turn signal. As shown in the figure, Gently clip the pre installed car turn signal light onto the card hole on the body of the car, making sure the position of the card is accurate. There is a small iron plate on one side of the turn signal light, so we need to install the plastic side first, and then gently fasten the side with the small iron plate!

FAW Toyota Yize IZOA introduce

The Yize IZOA, as the first model under FAW Toyota based on the TNGA architecture, does not continue the fixed mode of small cars with small displacement, but is equipped with a "large displacement" TNGA 2.0L naturally aspirated engine. The TNGA 2.0L engine has entered the domestic stage, and through technologies such as improving thermal efficiency, reducing friction resistance, and controlling intake and exhaust valves, its power performance is improved by 15% -20% compared to traditional 2.0L engines, The fuel economy has improved by 25%. The Yize IZOA transmission system is matched with a 6MT or CVT gearbox. In terms of appearance, the Yize IZOA will draw inspiration from the design elements of the Fengchao Way concept car. The front grille is equipped with a horizontal air intake grille and two angled headlights on both sides, and the lower grille adopts an inverted trapezoidal shape with a black mesh design inside. The traditional straight waistline is diluted, and the exaggerated front and rear wheel arches are connected by a flowing arc, The large area anti friction protection panel is full of wildness. The second row doors of the new car are equipped with hidden door handles, similar to the Honda XR-V, and the unique "boomerang" LED light group at the rear is impressive. The Yize IZOA continues the design style of the American version C-HR, leaning towards the driver's side as a whole, equipped with a three spoke multifunctional steering wheel, integrated with Bluetooth phone, multimedia playback and other control keys. The instrument panel adopts a double barrel shape, The center is equipped with a driving computer. The top of the center console is equipped with an 8-inch floating display screen, supporting HMI human-machine interaction system, and the bottom is the air conditioning area control key