Front and rear door hinges introduce

Also known as door hinge, it is used for opening and closing doors. Hinges, also known as hinges, are mechanical devices used to connect two solids and allow relative rotation between them. Hinges can be composed of movable components or foldable materials. The main feature is to provide cushioning when the cabinet or door is closed, minimizing the noise generated by collisions with other parts when the door is closed. Car hinges are generally used in car doors and engine hood, And the trunk lid, fuel tank lid hinge, etc. In order to connect the car door to the body, the hinge is responsible for connecting the car door to the body, ensuring the opening and closing of the car door, and allowing the car door to open and close, so there is a door hinge. Its main function is to connect the car body to the car door. Generally, The door hinge should consist of at least three parts. 1. Body parts connected to the vehicle body. 2. Door parts connected to the door. 3. Other parts that connect the body parts and door parts and ensure that the door hinge can make opening and closing movements)

The installation of car doors requires the following processes:

The installation of car doors requires the following steps: 1. First, prepare the new car door that needs to be replaced and installed. Place the new car door on a paper shell to avoid scratching the new door, and prepare the necessary tools for installation, including a large wheel, a small wheel, a No. 13 sleeve, a No. 6 sleeve, and a small hammer. Then, start the operation process. 2. Install the door hinges, where a large wheel is required, Cooperate with sleeve 13. Take out the door hinge, fix the screws of the door hinge, and then make a rough comparison by hand to check whether the hole of the hinge is the same size as the screw hole of the door, and whether the screw can be screwed in exactly. Do a good job of inspection. 3. After comparing the hinge by hand, take out the large wheel and match it with sleeve 13. Gently tighten the screws that fix the hinge to the door by hand, and then use tools to tighten it. If you use tools to tighten it directly, It is easy to break the screws, which results in the entire car door being scrapped. Therefore, when tightening, be careful and slow. Pay attention to the extended part of the hinge head facing downwards, as it needs to be inserted into the card slot of the car body hinge. 4. Lift the door with the installed hinge by hand and lift it to the installation position of the car body door. There are two hinge holes on the installation position of the car body door, and the extended part of the hinge head on the new car door should be aligned up and down, Insert it into the two hinge holes on the car body. Be sure to take it slow and align the upper and lower holes before inserting it to avoid scratching the paint surface on the car body. 5. The extended part of the inserted hinge may get stuck halfway through the holes, which is a common problem, but it is also easy to solve. Take out the hammer and smash the hinge on the car door twice with the hammer, and the extended part will enter the car body hole. 6. Next, remove the screw that fixes the car body hinge, There is a screw hole in the middle part of the body hinge hole, which is used to fix the body hinge and door hinge. First, gently screw in a part by hand to avoid damaging the screw directly with tools. The screw on the door should be fixed with extra care. 7. Take out the small wheel, long extension rod, and No. 6 sleeve, and tighten the screw that has been screwed in by hand with tools. There are a total of two screws, up and down, which are also completed according to the above procedure. It should be noted that:, Be sure to steadily and tentatively tighten the screws bit by bit in order to complete the task smoothly

FAW Toyota Yize IZOA introduce

The Yize IZOA, as the first model under FAW Toyota based on the TNGA architecture, does not continue the fixed mode of small cars with small displacement, but is equipped with a "large displacement" TNGA 2.0L naturally aspirated engine. The TNGA 2.0L engine has entered the domestic stage, and through technologies such as improving thermal efficiency, reducing friction resistance, and controlling intake and exhaust valves, its power performance is improved by 15% -20% compared to traditional 2.0L engines, The fuel economy has improved by 25%. The Yize IZOA transmission system is matched with a 6MT or CVT gearbox. In terms of appearance, the Yize IZOA will draw inspiration from the design elements of the Fengchao Way concept car. The front grille is equipped with a horizontal air intake grille and two angled headlights on both sides, and the lower grille adopts an inverted trapezoidal shape with a black mesh design inside. The traditional straight waistline is diluted, and the exaggerated front and rear wheel arches are connected by a flowing arc, The large area anti friction protection panel is full of wildness. The second row doors of the new car are equipped with hidden door handles, similar to the Honda XR-V, and the unique "boomerang" LED light group at the rear is impressive. The Yize IZOA continues the design style of the American version C-HR, leaning towards the driver's side as a whole, equipped with a three spoke multifunctional steering wheel, integrated with Bluetooth phone, multimedia playback and other control keys. The instrument panel adopts a double barrel shape, The center is equipped with a driving computer. The top of the center console is equipped with an 8-inch floating display screen, supporting HMI human-machine interaction system, and the bottom is the air conditioning area control key