• Website for purchasing dismantled parts
  • 8:00-18:00
Besturn B70 Half shaft

Besturn B70 Half shaft

  • Price:please consult customer service
  • Transportation costs:Negotiate with sales personnel

number:

Half shaft introduce

Driver Shaft, also known as CVJ, CV joint, constant velocity joint, is a shaft that transmits torque between the gearbox reducer and the drive wheel. It has a U-joint at the inner and outer ends, which is connected to the reducer gear and the inner ring of the hub bearing through splines on the U-joint [2] The half shaft is the shaft that transfers torque between the gearbox reducer and the drive wheel (previously mostly solid, but due to the uneven rotation control of the hollow shaft, many cars use hollow shafts). It has a universal joint (U/JOIN) at the inner and outer ends, which is connected to the reducer gear and the inner ring of the hub bearing through splines on the universal joint. There are two types of half shafts commonly used in modern cars, full floating and semi floating, depending on their support types (There are also three types, namely fully floating. 3/4 floating and semi floating.) The fully floating half axle only transmits torque and does not withstand any reaction force or bending moment. When combined with independent suspension, it is beneficial to improve vehicle comfort and is widely used in various types of cars. The fully floating half axle is easy to disassemble, and during maintenance and repair, the half axle can be removed by simply unscrewing the fixing bolts of the half axle, while the wheels and axle housing can still support the car, Thus, it brings convenience to car maintenance. The semi floating half axle not only transmits torque but also bears all reaction forces and bending moments. Its supporting structure is simple and low in cost, mainly suitable for pickup trucks and SUVs that do not require high comfort requirements. However, this type of half axle support is difficult to remove, and if the half axle breaks during driving, it is easy to cause the risk of wheels flying off, which is a form that is about to be phased out)

Steps for disassembling and installing the rear axle half shaft of a car

The steps for disassembling and assembling the rear axle half shaft of a car are as follows: 1. Lift the car and support it reliably. Remove the rear suspension swing arm bolts; 2. Remove the fixing bolts and covers of the outer cross shaft universal joint, and remove the fixing bolts and covers of the inner cross shaft universal joint; 3. Slide the half shafts together, do not apply too much force, remove the half shafts, do not let them hang vertically, to prevent damage to the universal joint bearings caused by impact; 4. Check if the universal joint assembly is worn or damaged, and if necessary, replace the universal joint; 5. When installing the rear axle half shaft, first install the half shaft onto the inner universal joint. The diameter of the inner half shaft is larger than that of the outer half shaft. Install the universal joint fixing cover and fixing bolts, and tighten the bolts with the corresponding torque. Note: Make sure to use Loctite glue on the universal joint fixing bolts; 6. Install the half shaft onto the outer universal joint, install the universal joint fixing cover and fixing bolts, and tighten the bolts with the corresponding torque; 7. Install the rear suspension swing arm and tighten the bolts to the corresponding torque

Besturn B70 introduce

The Pentium B70 has a small change. It is a highly anticipated independent product of FAW sedan. Although it heavily draws on the technology of the joint venture Mazda 6 and is produced in the same line as Mazda 6, it is a true independent brand product. The Pentium B70 has undergone 3 million kilometers of road testing and has undergone 518 inspections The launch of this car not only demonstrates the strong technical strength of FAW Pentium, but also reflects its development strategy of focusing on green and environmental protection, as well as independent technological innovation. From previous test cars, the new generation B70 adopts the Pentium family's hexagonal grille on the front face, and the headlights also adopt a wing shaped contour design. From the appearance of the B90 at the Beijing Auto Show, The replacement B70 may adopt the family front face design of the new generation Pentium family represented by the B90

Customer Reviews

  • 1.We will vary based on your shipping address and the chosen delivery method, and the general delivery time is 1-7 days
  • 2.All products sold and shipped from our company are genuine commercial accessories
  • 3.Each order comes with a Chinese printed "outbound list", which can be used as a unit accounting voucher and will be shipped together with the package
  • 4.If replacement is required, please keep the accessories clean and intact in packaging, along with the delivery note, and send them back. Our company promises to guarantee return and exchange within 15 days
  • 5.Special note: ordering accessories from the manufacturer is not covered by the warranty

Other Parts