cylinder head introduce

The cylinder head is installed on top of the cylinder block, sealing the cylinder from the top and forming the combustion chamber. It often comes into contact with high-temperature and high-pressure gas, so it bears a large thermal and mechanical load. The cylinder head of a water-cooled engine is equipped with a cooling water jacket, and the cooling water hole on the lower end face of the cylinder head is connected to the cooling water hole of the cylinder block. Circulating water is used to cool the high-temperature parts of the combustion chamber. The cylinder head is also equipped with inlet and exhaust valve seats, valve guide holes, and is used to install inlet and exhaust valves, There are also intake and exhaust channels. The cylinder head of gasoline engines is equipped with holes for installing spark plugs, while the cylinder head of diesel engines is equipped with holes for installing fuel injectors. The cylinder head of overhead camshaft engines is also equipped with camshaft bearing holes for installing camshafts. The cylinder head is generally made of gray cast iron or alloy cast iron, and aluminum alloy has good thermal conductivity, which is conducive to improving compression ratio. The cylinder head is an integral part of the combustion chamber, The shape of the combustion chamber has a significant impact on the operation of the engine. Due to the different combustion methods of gasoline and diesel engines, there is a significant difference in the parts that make up the combustion chamber on the cylinder head. The combustion chamber of gasoline engines is mainly on the cylinder head, while the combustion chamber of diesel engines is mainly on the concave pit at the top of the piston. 1. The cylinder head bolts should be tightened evenly and the fuel supply time should be adjusted correctly. 2. Soft water should be added to the water tank, And try to change water as little as possible. 3. The engine should avoid working under overload for a long time. 4. When the engine is working and the water tank occasionally runs out of water, do not immediately turn off the engine. Instead, slowly add water at low speed. Do not add cold water after the engine heats up. After parking, wait for the water temperature to below 40 ℃ before adding water. In cold winter, do not add water immediately when starting, Instead, heat the water first and add boiling water. During assembly, check whether each cooling water hole is unobstructed. Regularly clean the cooling system with alkaline solution and promptly remove scale and oil stains [1])

The installation steps for the cylinder head are as follows:

The installation steps of the cylinder head are as follows: The installation of the cylinder head should be carried out in the order of disassembly first and then installation, and the following issues should be noted during the assembly process: 01 Before installing the cylinder head, the crankshaft should be turned to the top dead center position of the first cylinder. 02 When installing the cylinder head gasket, the side marked with the part number must be visible. 03 Replace the cylinder head fastening bolts, Do not reuse bolts that have been tightened according to the tightening torque. 04 Tighten the cylinder head bolts to a torque of 40N · m in the sequence shown in the following figure, and then use a wrench to tighten 180 °. Tighten the cylinder head bolts to a torque of 40N · m in the sequence shown in the figure. 05 Install the timing belt (adjust the valve timing phase), install the valve cover. 06 Adjust the throttle lock, Add new coolant. 07 Perform throttle control unit matching. 08 Query fault codes. Removing the electronic component plug of the electronic control unit will cause fault storage. Query fault codes and delete them if necessary. 09 Pay attention to the tightening torque of the main component bolts. The tightening torque of the front exhaust pipe and exhaust manifold fastening bolts is 20N · m, and the tightening torque of the fastening bolt between the intake manifold bracket and the engine is 20N · m, The tightening torque of the fastening bolts between the intake manifold bracket and intake manifold is 30N · m

Fox Active introduce

Relying on Ford's strong SUV research and development capabilities and manufacturing heritage, inheriting the excellent handling genes of Focus, the new Focus Active SUV model of the Focus family - the urban cutting-edge SUV - has been launched brilliantly. With excellent handling, excellent passability, trendy appearance, and leading technology, it better meets the diversified driving needs of the emerging post-90s consumers, with a price range of 139800 yuan to 153800 yuan. The Focus SUV is equipped with a 1.5-liter EcoBoost that integrates more than 20 cutting-edge technologies ® The turbocharged dual injection engine, paired with an 8-speed automatic transmission, can achieve a maximum power of 128 kW and a peak torque of 243 Nm Equipped with a multi road condition management system, including 5 driving modes including standard, sporty, economical, anti slip, and rough road surfaces, it can better cope with complex road conditions such as snow, mud, and gravel. The body is made of 1500 megapascals ultra-high strength material, which not only ensures safety but also provides better anti torsion performance, making handling more agile The Focus SUV is equipped with the representative Ford Co Pilot360 ™ The Intelligent Driving Assistance System integrates more than 10 leading driving assistance technologies, achieving L2 level autonomous driving. It is also equipped with the SYNC Intelligent Driving Information Entertainment System, jointly developed by Ford and Baidu with a 12.3-inch horizontally leading central control screen, bringing a more intelligent and interconnected upgrade experience for Chinese consumers. Today, the all-new Focus Active was launched on FUN DAY Ford Brand Day! As an SUV launched under the Fox family, the all-new Fox Active relies on the Ford brand's research and development capabilities and manufacturing heritage, inheriting the Fox family's control genes, and creating an urban cutting-edge SUV that combines excellent handling, excellent passability, trendy appearance, and leading technology, meeting the diverse driving needs of post-90s consumers