Front and rear door hinges introduce

Also known as door hinge, it is used for opening and closing doors. Hinges, also known as hinges, are mechanical devices used to connect two solids and allow relative rotation between them. Hinges can be composed of movable components or foldable materials. The main feature is to provide cushioning when the cabinet or door is closed, minimizing the noise generated by collisions with other parts when the door is closed. Car hinges are generally used in car doors and engine hood, And the trunk lid, fuel tank lid hinge, etc. In order to connect the car door to the body, the hinge is responsible for connecting the car door to the body, ensuring the opening and closing of the car door, and allowing the car door to open and close, so there is a door hinge. Its main function is to connect the car body to the car door. Generally, The door hinge should consist of at least three parts. 1. Body parts connected to the vehicle body. 2. Door parts connected to the door. 3. Other parts that connect the body parts and door parts and ensure that the door hinge can make opening and closing movements)

The installation of car doors requires the following processes:

The installation of car doors requires the following steps: 1. First, prepare the new car door that needs to be replaced and installed. Place the new car door on a paper shell to avoid scratching the new door, and prepare the necessary tools for installation, including a large wheel, a small wheel, a No. 13 sleeve, a No. 6 sleeve, and a small hammer. Then, start the operation process. 2. Install the door hinges, where a large wheel is required, Cooperate with sleeve 13. Take out the door hinge, fix the screws of the door hinge, and then make a rough comparison by hand to check whether the hole of the hinge is the same size as the screw hole of the door, and whether the screw can be screwed in exactly. Do a good job of inspection. 3. After comparing the hinge by hand, take out the large wheel and match it with sleeve 13. Gently tighten the screws that fix the hinge to the door by hand, and then use tools to tighten it. If you use tools to tighten it directly, It is easy to break the screws, which results in the entire car door being scrapped. Therefore, when tightening, be careful and slow. Pay attention to the extended part of the hinge head facing downwards, as it needs to be inserted into the card slot of the car body hinge. 4. Lift the door with the installed hinge by hand and lift it to the installation position of the car body door. There are two hinge holes on the installation position of the car body door, and the extended part of the hinge head on the new car door should be aligned up and down, Insert it into the two hinge holes on the car body. Be sure to take it slow and align the upper and lower holes before inserting it to avoid scratching the paint surface on the car body. 5. The extended part of the inserted hinge may get stuck halfway through the holes, which is a common problem, but it is also easy to solve. Take out the hammer and smash the hinge on the car door twice with the hammer, and the extended part will enter the car body hole. 6. Next, remove the screw that fixes the car body hinge, There is a screw hole in the middle part of the body hinge hole, which is used to fix the body hinge and door hinge. First, gently screw in a part by hand to avoid damaging the screw directly with tools. The screw on the door should be fixed with extra care. 7. Take out the small wheel, long extension rod, and No. 6 sleeve, and tighten the screw that has been screwed in by hand with tools. There are a total of two screws, up and down, which are also completed according to the above procedure. It should be noted that:, Be sure to steadily and tentatively tighten the screws bit by bit in order to complete the task smoothly

BYD L3 introduce

From the perspective of BYD's product system, the F3 is gradually moving towards the low-end, the G3 is moving towards the mid-range, and the L3 will be the first bullet in BYD's mid to high end models. The positioning of this car will be close to or slightly higher than the currently available compact car G3. With BYD's consistent high cost-effectiveness, it is expected to compete in the higher end automotive market and potentially impact the current compact car market dominated by joint venture brands The L3 front face features a wide and thick dual horizontal bar intake grille that is simple and atmospheric; The overall shape of the front headlights adopts a tear eye design, while the smoked black design adds a sporty style to the entire vehicle. The engine hood also adopts the popular raised design, making the overall style very linear and powerful. It can be seen that the L3 has surpassed the past in appearance design, forming a distinct style. The tail lights are designed with popular LED lights, which exude a grand, fashionable, elegant temperament, and reliable safety and quality