Front door interior panel introduce

The part names of the interior panel of the left front door, from top to bottom, are: left front door glass, left front mirror, left front glass sealing strip, those with decorative strips on the outside are called left front door decorative strip. The left front door is decomposed into left front door, mirror, glass, door lock, door glass controller, door glass elevator, mirror controller, left front door interior panel, handle, etc. The car is structurally divided into frame, outer panel, chassis, engine, interior, glass, tire, and is functionally divided into electrical system and driving system Driving system, oil and gas system, filtration system, control system, cooling system)

Installation method of front door interior panel/rear door interior panel

1、 Prepare tools and work vehicles or workbenches. 2. Open the car door to its maximum size for easier operation of the hinge support. Place a bracket at the lower edge of the car door to support the weight of the door and protect it. Unscrew the window glass. In this example, the disassembly of the car door will be mainly introduced. If the car door needs to be disassembled before disassembly, the outdoor rearview mirror should be removed. 3. Disconnect the wire connector between the car door and the vehicle body to separate the door wiring harness, If necessary, first remove the inner decorative parts on the pillar. 4. Remove the clamp at the bottom of the door stopper locking pin and extract the locking pin from the hole. 5. Hold the door and remove the connecting bolt of the door hinge support. After removing the door, place it vertically on a padded surface. If only the door needs to be removed for maintenance, it is recommended to complete the disassembly of the door by removing the hinge connecting bolt instead of the fixed bolt, This can reduce the adjustment work of the car door. 6. Check the sleeve of the car door chain, replace it if necessary, lubricate the hinge joint, place the car door back on the hinge support, and reinstall the bolts. 7. Connect the door limiter, install the stop lock pin and locking plate, and connect the electrical plug. 8. Close the car door, check if it is aligned, and if there is no problem, tighten the hinge fixing bolts. 9. Note that if the front door is disassembled and assembled, it is necessary to install the rearview mirror back

Cheetah CT5 introduce

Anhui Leopard Automobile Co., Ltd. was established on March 28, 2005. It is the strategic core enterprise of Hunan Changfeng Group (Leopard Automobile) in Chuzhou, and also the second largest vehicle production base after the Changsha headquarters and Yongzhou base. The company currently covers an area of about 466.3 acres, including a construction area of 60000 square meters, a registered capital of 600 million yuan, and 860 employees, including 258 people with college degrees or above, and 260 people with various professional qualifications, There are a total of 57 personnel with intermediate or above professional titles, including 50 technical line engineers and above. Currently, the total assets are about 520 million yuan, with a debt ratio of 46%. Since its establishment, the company has invested a huge amount of money in technological transformation of its original production scale, and has formed an annual production capacity of 10000 units per shift. The main products are the three series of pickup trucks and SUV series, including the Flybell, Flyer, and CT5, covering three levels: low, medium, and high, Capable of industrialization in the research and development, manufacturing, quality assurance, and marketing of pickup trucks and SUVs The overall relocation, upgrading and renovation project of the company was signed on February 22, 2013, and received approval from the Ministry of Industry and Information Technology of China. The project has a total investment of 2921.74 million yuan, covers an area of 985 acres, a total construction area of 193446 square meters, a production value of 9.47 billion yuan, a profit of 758 million yuan, and a tax payment of 330 million yuan. In April 2013, The project will commence construction. It is planned to complete the design, construction, procurement, and manufacturing of equipment and fixtures for the process, civil engineering, and public works within 18 months. Trial production will begin in September 2014, and production will reach the standard in January 2016 In 2013, the company achieved a total output value of 420 million yuan, and in the first quarter of 2014, it achieved a output value of 220 million yuan, a year-on-year increase of 8.5%