Front and rear door hinges introduce

Also known as door hinge, it is used for opening and closing doors. Hinges, also known as hinges, are mechanical devices used to connect two solids and allow relative rotation between them. Hinges can be composed of movable components or foldable materials. The main feature is to provide cushioning when the cabinet or door is closed, minimizing the noise generated by collisions with other parts when the door is closed. Car hinges are generally used in car doors and engine hood, And the trunk lid, fuel tank lid hinge, etc. In order to connect the car door to the body, the hinge is responsible for connecting the car door to the body, ensuring the opening and closing of the car door, and allowing the car door to open and close, so there is a door hinge. Its main function is to connect the car body to the car door. Generally, The door hinge should consist of at least three parts. 1. Body parts connected to the vehicle body. 2. Door parts connected to the door. 3. Other parts that connect the body parts and door parts and ensure that the door hinge can make opening and closing movements)

The installation of car doors requires the following processes:

The installation of car doors requires the following steps: 1. First, prepare the new car door that needs to be replaced and installed. Place the new car door on a paper shell to avoid scratching the new door, and prepare the necessary tools for installation, including a large wheel, a small wheel, a No. 13 sleeve, a No. 6 sleeve, and a small hammer. Then, start the operation process. 2. Install the door hinges, where a large wheel is required, Cooperate with sleeve 13. Take out the door hinge, fix the screws of the door hinge, and then make a rough comparison by hand to check whether the hole of the hinge is the same size as the screw hole of the door, and whether the screw can be screwed in exactly. Do a good job of inspection. 3. After comparing the hinge by hand, take out the large wheel and match it with sleeve 13. Gently tighten the screws that fix the hinge to the door by hand, and then use tools to tighten it. If you use tools to tighten it directly, It is easy to break the screws, which results in the entire car door being scrapped. Therefore, when tightening, be careful and slow. Pay attention to the extended part of the hinge head facing downwards, as it needs to be inserted into the card slot of the car body hinge. 4. Lift the door with the installed hinge by hand and lift it to the installation position of the car body door. There are two hinge holes on the installation position of the car body door, and the extended part of the hinge head on the new car door should be aligned up and down, Insert it into the two hinge holes on the car body. Be sure to take it slow and align the upper and lower holes before inserting it to avoid scratching the paint surface on the car body. 5. The extended part of the inserted hinge may get stuck halfway through the holes, which is a common problem, but it is also easy to solve. Take out the hammer and smash the hinge on the car door twice with the hammer, and the extended part will enter the car body hole. 6. Next, remove the screw that fixes the car body hinge, There is a screw hole in the middle part of the body hinge hole, which is used to fix the body hinge and door hinge. First, gently screw in a part by hand to avoid damaging the screw directly with tools. The screw on the door should be fixed with extra care. 7. Take out the small wheel, long extension rod, and No. 6 sleeve, and tighten the screw that has been screwed in by hand with tools. There are a total of two screws, up and down, which are also completed according to the above procedure. It should be noted that:, Be sure to steadily and tentatively tighten the screws bit by bit in order to complete the task smoothly

Cheetah CT5 introduce

Anhui Leopard Automobile Co., Ltd. was established on March 28, 2005. It is the strategic core enterprise of Hunan Changfeng Group (Leopard Automobile) in Chuzhou, and also the second largest vehicle production base after the Changsha headquarters and Yongzhou base. The company currently covers an area of about 466.3 acres, including a construction area of 60000 square meters, a registered capital of 600 million yuan, and 860 employees, including 258 people with college degrees or above, and 260 people with various professional qualifications, There are a total of 57 personnel with intermediate or above professional titles, including 50 technical line engineers and above. Currently, the total assets are about 520 million yuan, with a debt ratio of 46%. Since its establishment, the company has invested a huge amount of money in technological transformation of its original production scale, and has formed an annual production capacity of 10000 units per shift. The main products are the three series of pickup trucks and SUV series, including the Flybell, Flyer, and CT5, covering three levels: low, medium, and high, Capable of industrialization in the research and development, manufacturing, quality assurance, and marketing of pickup trucks and SUVs The overall relocation, upgrading and renovation project of the company was signed on February 22, 2013, and received approval from the Ministry of Industry and Information Technology of China. The project has a total investment of 2921.74 million yuan, covers an area of 985 acres, a total construction area of 193446 square meters, a production value of 9.47 billion yuan, a profit of 758 million yuan, and a tax payment of 330 million yuan. In April 2013, The project will commence construction. It is planned to complete the design, construction, procurement, and manufacturing of equipment and fixtures for the process, civil engineering, and public works within 18 months. Trial production will begin in September 2014, and production will reach the standard in January 2016 In 2013, the company achieved a total output value of 420 million yuan, and in the first quarter of 2014, it achieved a output value of 220 million yuan, a year-on-year increase of 8.5%