Rear wheel fender introduce

The leaf plate includes: front leaf plate, front leaf plate lining, front leaf plate light, rear leaf plate light, radiator frame. The leaf plate refers to a type of cover on motor vehicles and non motor vehicles (a slightly protruding, semi-circular small piece above the wheel), and the cover, as the name suggests, is the shell that covers the outside of motor vehicles and non motor vehicles. It conforms to fluid mechanics and reduces the wind resistance coefficient, Make the car run more smoothly. The fender, also known as the fender, is located outside the body of the wheels. Its function is to reduce the drag coefficient of the fender air outlet according to fluid dynamics, making the car run more smoothly. According to the installation position, it is divided into front fender and rear fender. The front fender is installed above the front wheel, because the front wheel has steering function, it is necessary to ensure the maximum limit space when the front wheel rotates, Therefore, designers will use a "wheel runout chart" to verify the design dimensions of the fender based on the selected tire model size. The rear fender does not have the problem of wheel rotation collision, but due to aerodynamic considerations, the rear fender slightly arches outward. Secondly, the front fender can prevent sand, stones, and mud rolled up by the wheels from splashing onto the bottom of the car during driving, reducing damage and corrosion to the chassis, The materials used are required to have weather aging resistance and good formability. Currently, many car front fenders are made of plastic materials with a certain degree of elasticity, making them more cushioning and safer)

Installation method of rear fender/rear fender assembly

1. Start the car and turn all wheels to the right, then turn off the engine and remove the car key. Then open the engine hood and disconnect the negative pole of the battery. Use a Phillips screwdriver to remove the four screws on the front bumper. Use a 5mm hex wrench to remove the two screws on the side of the front bumper; 2. Use a Phillips screwdriver and a 7mm socket to remove the three screws under the right side of the front bumper fascia. Use a Phillips screwdriver and a 7mm socket to remove the three screws of the fender. Remove the splash guard; 3. Use a small ratchet wrench, extension rod, and 7mm socket to remove the screws at the bottom of the front bumper. Use a square screwdriver and 7mm socket to remove the screws connecting the fender and bumper. Use a large ratchet wrench and 10mm socket to remove the four bolts behind the front headlight; 4. Remove the plug of the front headlight assembly. Remove the front headlight assembly. Remove the screws connecting the splash guard to the fender, and the fender can be removed; 5. The fender is located outside the vehicle body of the wheels. Its function is to reduce the drag coefficient based on fluid dynamics, making the vehicle travel smoother. It is further divided into front fender and rear fender according to the installation position, with the front fender installed above the front wheel; 6. Due to the steering function of the front wheels, it is necessary to ensure the maximum limit space when the front wheels rotate. Therefore, the designer will use the "wheel runout diagram" based on the selected tire model size to verify the design size of the fender

Cheetah CT5 introduce

Anhui Leopard Automobile Co., Ltd. was established on March 28, 2005. It is the strategic core enterprise of Hunan Changfeng Group (Leopard Automobile) in Chuzhou, and also the second largest vehicle production base after the Changsha headquarters and Yongzhou base. The company currently covers an area of about 466.3 acres, including a construction area of 60000 square meters, a registered capital of 600 million yuan, and 860 employees, including 258 people with college degrees or above, and 260 people with various professional qualifications, There are a total of 57 personnel with intermediate or above professional titles, including 50 technical line engineers and above. Currently, the total assets are about 520 million yuan, with a debt ratio of 46%. Since its establishment, the company has invested a huge amount of money in technological transformation of its original production scale, and has formed an annual production capacity of 10000 units per shift. The main products are the three series of pickup trucks and SUV series, including the Flybell, Flyer, and CT5, covering three levels: low, medium, and high, Capable of industrialization in the research and development, manufacturing, quality assurance, and marketing of pickup trucks and SUVs The overall relocation, upgrading and renovation project of the company was signed on February 22, 2013, and received approval from the Ministry of Industry and Information Technology of China. The project has a total investment of 2921.74 million yuan, covers an area of 985 acres, a total construction area of 193446 square meters, a production value of 9.47 billion yuan, a profit of 758 million yuan, and a tax payment of 330 million yuan. In April 2013, The project will commence construction. It is planned to complete the design, construction, procurement, and manufacturing of equipment and fixtures for the process, civil engineering, and public works within 18 months. Trial production will begin in September 2014, and production will reach the standard in January 2016 In 2013, the company achieved a total output value of 420 million yuan, and in the first quarter of 2014, it achieved a output value of 220 million yuan, a year-on-year increase of 8.5%