Front turn signal introduce

Turn signal is an important indicator light that is activated when a motor vehicle turns to remind the front, rear, left, right, and pedestrians to pay attention. The turn signal tube uses xenon gas tubes, a microcontroller control circuit, and the left and right rotate continuously to flash. The turn signal uses a flasher to achieve light flashing. It can be mainly divided into three types: wire blocking, capacitive, and electronic. Among them, wire blocking can be further divided into hot wire (electric heating) and wing type (bouncing), Electronic flashers can be divided into hybrid (with contact relays and electronic components) and fully electronic (without relays). For example, pop-up flashers use the principle of electric current thermal effect, which uses thermal expansion and contraction as power to cause sudden changes in the spring plate to connect and disconnect the contacts, achieving flashing lights. Turn signals are the most important device that represents the dynamic information of the car, installed in front and behind the body, and can be turned on when the car turns, providing safety assurance for driving, For your and others' safety, please use turn signals according to regulations, so that people can know the direction of the car in advance and make correct judgments)

Installation of front turn signals/rear turn signals/LED daytime running lights/side marker lights/front and rear position lights

Tool preparation: 1. First, we need to prepare the tools required for the entire process of installing car turn signals, including a screwdriver and a wire hook. Then, we need to prepare the car turn signals that need to be installed. 2. Turn on the double flash. As shown in the figure, open the car's key door, and press the switch button of the double flash by hand. This way, the car's double flash will open. Observe the position of the turn signal wire harness. Now we can take out the iron hook, You can make this iron hook yourself, just put it on a wire head. It's quite simple because we have a dual flash, so we can observe the position of the turn signal harness through the hole. 3. Hook out the turn signal. As shown in the figure, after we find the position of the turn signal harness, we use the small iron hook made to hook the harness, and then hook out the turn signal. Be careful to hook it slowly, Avoid disconnecting the wiring harness, and also be careful not to scratch the surface of the car, which may affect its appearance. For the first time installing a car turn signal, as shown in the figure, take out the car turn signal that needs to be installed. Let's take a closer look. There are two small snap holes on the turn signal lampshade that can be directly attached to the turn signal. Please find a good position and gently attach the turn signal to the lampshade. 4. Installation of the car turn signal. As shown in the figure, Gently clip the pre installed car turn signal light onto the card hole on the body of the car, making sure the position of the card is accurate. There is a small iron plate on one side of the turn signal light, so we need to install the plastic side first, and then gently fasten the side with the small iron plate!

Dongfeng Xiaokang C37 introduce

Appearance: The Dongfeng Xiaokang C37 has a sharp and angular exterior design. When you first see it, you will always feel a bit like the new generation Quanshun. The square and square shape adds a stronger business atmosphere to it. Basic parameters: The exterior dimensions are 4500 * 1680 * 1960mm, with a wheelbase of 3050mm. Compared with other competing models, the Dongfeng Xiaokang C37 should be considered a big block in micro passenger products. The vertically placed headlight assembly looks very personalized, The appearance of the Fangzheng is consistent with the overall style of the vehicle. The large intake grille adopts two thick horizontal bar designs, giving a domineering and tough feeling. Interior: The center console is wrapped in hard plastic, and according to the editing experience, the seams between various components are even without any burrs or other phenomena. The center console adopts a color combination of deep top and light bottom, which meets the aesthetic requirements of Chinese people. Space: The interior space of the Dongfeng Xiaokang C37 is still very good, Even for the 9-seat model with the largest number of seats, the interior space will not feel particularly cramped, and the middle two rows of seats can also be adjusted back and forth, which is more practical. Power: Dongfeng Xiaokang C37 is equipped with a 1.4L all aluminum engine, model DK13-06, the maximum power is 101 horsepower/6000 rpm, the maximum torque is 124N · m/5200 rpm, and the transmission is a 5-gear manual transmission. This engine uses a variable valve timing system, Fully meet the intake requirements of the engine at different speeds. In terms of configuration, the Dongfeng Xiaokang C37 comes standard with 185R14LT wide tires, aluminum alloy wheels, power steering, front electric windows, and child safety locks. In addition, the high-end models of Dongfeng Xiaokang are also equipped with leather seats and visual radar, and can also be equipped with ABS and driver's safety airbags