cylinder head introduce

The cylinder head is installed on top of the cylinder block, sealing the cylinder from the top and forming the combustion chamber. It often comes into contact with high-temperature and high-pressure gas, so it bears a large thermal and mechanical load. The cylinder head of a water-cooled engine is equipped with a cooling water jacket, and the cooling water hole on the lower end face of the cylinder head is connected to the cooling water hole of the cylinder block. Circulating water is used to cool the high-temperature parts of the combustion chamber. The cylinder head is also equipped with inlet and exhaust valve seats, valve guide holes, and is used to install inlet and exhaust valves, There are also intake and exhaust channels. The cylinder head of gasoline engines is equipped with holes for installing spark plugs, while the cylinder head of diesel engines is equipped with holes for installing fuel injectors. The cylinder head of overhead camshaft engines is also equipped with camshaft bearing holes for installing camshafts. The cylinder head is generally made of gray cast iron or alloy cast iron, and aluminum alloy has good thermal conductivity, which is conducive to improving compression ratio. The cylinder head is an integral part of the combustion chamber, The shape of the combustion chamber has a significant impact on the operation of the engine. Due to the different combustion methods of gasoline and diesel engines, there is a significant difference in the parts that make up the combustion chamber on the cylinder head. The combustion chamber of gasoline engines is mainly on the cylinder head, while the combustion chamber of diesel engines is mainly on the concave pit at the top of the piston. 1. The cylinder head bolts should be tightened evenly and the fuel supply time should be adjusted correctly. 2. Soft water should be added to the water tank, And try to change water as little as possible. 3. The engine should avoid working under overload for a long time. 4. When the engine is working and the water tank occasionally runs out of water, do not immediately turn off the engine. Instead, slowly add water at low speed. Do not add cold water after the engine heats up. After parking, wait for the water temperature to below 40 ℃ before adding water. In cold winter, do not add water immediately when starting, Instead, heat the water first and add boiling water. During assembly, check whether each cooling water hole is unobstructed. Regularly clean the cooling system with alkaline solution and promptly remove scale and oil stains [1])

The installation steps for the cylinder head are as follows:

The installation steps of the cylinder head are as follows: The installation of the cylinder head should be carried out in the order of disassembly first and then installation, and the following issues should be noted during the assembly process: 01 Before installing the cylinder head, the crankshaft should be turned to the top dead center position of the first cylinder. 02 When installing the cylinder head gasket, the side marked with the part number must be visible. 03 Replace the cylinder head fastening bolts, Do not reuse bolts that have been tightened according to the tightening torque. 04 Tighten the cylinder head bolts to a torque of 40N · m in the sequence shown in the following figure, and then use a wrench to tighten 180 °. Tighten the cylinder head bolts to a torque of 40N · m in the sequence shown in the figure. 05 Install the timing belt (adjust the valve timing phase), install the valve cover. 06 Adjust the throttle lock, Add new coolant. 07 Perform throttle control unit matching. 08 Query fault codes. Removing the electronic component plug of the electronic control unit will cause fault storage. Query fault codes and delete them if necessary. 09 Pay attention to the tightening torque of the main component bolts. The tightening torque of the front exhaust pipe and exhaust manifold fastening bolts is 20N · m, and the tightening torque of the fastening bolt between the intake manifold bracket and the engine is 20N · m, The tightening torque of the fastening bolts between the intake manifold bracket and intake manifold is 30N · m

Dongfeng Xiaokang C37 introduce

Appearance: The Dongfeng Xiaokang C37 has a sharp and angular exterior design. When you first see it, you will always feel a bit like the new generation Quanshun. The square and square shape adds a stronger business atmosphere to it. Basic parameters: The exterior dimensions are 4500 * 1680 * 1960mm, with a wheelbase of 3050mm. Compared with other competing models, the Dongfeng Xiaokang C37 should be considered a big block in micro passenger products. The vertically placed headlight assembly looks very personalized, The appearance of the Fangzheng is consistent with the overall style of the vehicle. The large intake grille adopts two thick horizontal bar designs, giving a domineering and tough feeling. Interior: The center console is wrapped in hard plastic, and according to the editing experience, the seams between various components are even without any burrs or other phenomena. The center console adopts a color combination of deep top and light bottom, which meets the aesthetic requirements of Chinese people. Space: The interior space of the Dongfeng Xiaokang C37 is still very good, Even for the 9-seat model with the largest number of seats, the interior space will not feel particularly cramped, and the middle two rows of seats can also be adjusted back and forth, which is more practical. Power: Dongfeng Xiaokang C37 is equipped with a 1.4L all aluminum engine, model DK13-06, the maximum power is 101 horsepower/6000 rpm, the maximum torque is 124N · m/5200 rpm, and the transmission is a 5-gear manual transmission. This engine uses a variable valve timing system, Fully meet the intake requirements of the engine at different speeds. In terms of configuration, the Dongfeng Xiaokang C37 comes standard with 185R14LT wide tires, aluminum alloy wheels, power steering, front electric windows, and child safety locks. In addition, the high-end models of Dongfeng Xiaokang are also equipped with leather seats and visual radar, and can also be equipped with ABS and driver's safety airbags