cylinder head introduce

The cylinder head is installed on top of the cylinder block, sealing the cylinder from the top and forming the combustion chamber. It often comes into contact with high-temperature and high-pressure gas, so it bears a large thermal and mechanical load. The cylinder head of a water-cooled engine is equipped with a cooling water jacket, and the cooling water hole on the lower end face of the cylinder head is connected to the cooling water hole of the cylinder block. Circulating water is used to cool the high-temperature parts of the combustion chamber. The cylinder head is also equipped with inlet and exhaust valve seats, valve guide holes, and is used to install inlet and exhaust valves, There are also intake and exhaust channels. The cylinder head of gasoline engines is equipped with holes for installing spark plugs, while the cylinder head of diesel engines is equipped with holes for installing fuel injectors. The cylinder head of overhead camshaft engines is also equipped with camshaft bearing holes for installing camshafts. The cylinder head is generally made of gray cast iron or alloy cast iron, and aluminum alloy has good thermal conductivity, which is conducive to improving compression ratio. The cylinder head is an integral part of the combustion chamber, The shape of the combustion chamber has a significant impact on the operation of the engine. Due to the different combustion methods of gasoline and diesel engines, there is a significant difference in the parts that make up the combustion chamber on the cylinder head. The combustion chamber of gasoline engines is mainly on the cylinder head, while the combustion chamber of diesel engines is mainly on the concave pit at the top of the piston. 1. The cylinder head bolts should be tightened evenly and the fuel supply time should be adjusted correctly. 2. Soft water should be added to the water tank, And try to change water as little as possible. 3. The engine should avoid working under overload for a long time. 4. When the engine is working and the water tank occasionally runs out of water, do not immediately turn off the engine. Instead, slowly add water at low speed. Do not add cold water after the engine heats up. After parking, wait for the water temperature to below 40 ℃ before adding water. In cold winter, do not add water immediately when starting, Instead, heat the water first and add boiling water. During assembly, check whether each cooling water hole is unobstructed. Regularly clean the cooling system with alkaline solution and promptly remove scale and oil stains [1])

The installation steps for the cylinder head are as follows:

The installation steps of the cylinder head are as follows: The installation of the cylinder head should be carried out in the order of disassembly first and then installation, and the following issues should be noted during the assembly process: 01 Before installing the cylinder head, the crankshaft should be turned to the top dead center position of the first cylinder. 02 When installing the cylinder head gasket, the side marked with the part number must be visible. 03 Replace the cylinder head fastening bolts, Do not reuse bolts that have been tightened according to the tightening torque. 04 Tighten the cylinder head bolts to a torque of 40N · m in the sequence shown in the following figure, and then use a wrench to tighten 180 °. Tighten the cylinder head bolts to a torque of 40N · m in the sequence shown in the figure. 05 Install the timing belt (adjust the valve timing phase), install the valve cover. 06 Adjust the throttle lock, Add new coolant. 07 Perform throttle control unit matching. 08 Query fault codes. Removing the electronic component plug of the electronic control unit will cause fault storage. Query fault codes and delete them if necessary. 09 Pay attention to the tightening torque of the main component bolts. The tightening torque of the front exhaust pipe and exhaust manifold fastening bolts is 20N · m, and the tightening torque of the fastening bolt between the intake manifold bracket and the engine is 20N · m, The tightening torque of the fastening bolts between the intake manifold bracket and intake manifold is 30N · m

Hafei Public Opinion M408 introduce

Hafei Minyi's multi sided and irregular headlights are eye-catching and dazzling. The overall design of the vehicle is full, with smooth lines, simple and rich in rhythm. While meeting its functions, it provides people with a beautiful enjoyment. Not only does it reflect the cultural heritage of the East, but it also exudes a strong modern atmosphere. It is an organic combination of carefree and carefree, rough and delicate, with strong foresight. Hafei Minyi's entire vehicle adopts a short nose, metal fully loaded body structure to reduce air resistance, Meet the requirements of collision regulations. Green and environmentally friendly fluorine free air conditioning system (optional), creating comfort and coolness in spring The heart of a car - the engine has strong power and can be equipped with multiple varieties of Dongan company's series of electronic fuel injection engines, meeting different output power requirements while meeting the Euro II standard for emissions While enjoying the pleasure of driving, safety is the most important. The seat belt is equipped with the driver's side airbag (optional) (co pilot airbag can also be optional) and ABS anti lock braking system (optional) to ensure your safety when traveling. The body structure also fully considers collision safety requirements, and a collision bar is installed inside the front door to enhance impact resistance; The Hafei public opinion frame adopts the internationally advanced beam section structure, with five crossbeams and three longitudinal beams arranged reasonably, simple and practical. After strength verification and simulation analysis, the front part of the longitudinal beam absorbs 70% of energy, fully meeting the requirements of collision regulations Comfortable and spacious seating space with 7-8 seats to choose from. The front seats can be adjusted front and rear to meet the requirements of drivers of different body types. The rear seats can be folded forward to provide convenience for loading At present, Hafei Minyi is the latest model in its series