rear axle assy introduce

The rear axle refers to a bridge that connects two rear wheels. The rear axle of a rear wheel drive vehicle is called the drive axle, while the rear axle of a non rear wheel drive vehicle is called the support axle. The rear suspension assembly often appears in passenger cars, A component generally composed of springs, shock absorbers, connecting rods, etc., which serves to transmit and support the excitation between the tire and the vehicle body. It is generally divided into three types of independent suspensions (link type), semi independent suspensions (torsion beam type), and non independent suspensions (axle or axle type). The rear axle refers to a bridge that connects two rear wheels. The rear axle of a rear wheel drive vehicle is called the drive axle, and the rear axle of a non rear wheel drive vehicle is called the support axle, The rear suspension assembly refers to the independent suspension system used to support the rear body of a vehicle)

Installation method of rear axle assembly/front axle assembly

1. Unscrew the oil drain plug at the bottom of the axle housing and drain the lubricating oil from the axle housing; Remove the connecting bolts between the flange of the driving bevel gear and the transmission shaft; 2. Disassembly of the half shaft. Before disassembly, cover the front wheels with a wooden cover and release the parking brake. When disassembling, loosen and unscrew all half shaft fastening nuts and washers; Gently strike the center of the rear end of the half shaft 2 to 3 times with a copper hammer to separate the half shaft flange surface from the hub connection surface. Then, pull the half shaft flange by hand to extract the half shaft. Note that when the spline part of the half shaft is about to pass through the oil seal, hold the half shaft rod with your hand and slowly rotate the half shaft to move it out in parallel, so as not to damage the half shaft oil seal and prevent it from falling and injuring people; 3. Disassembly of the main reducer assembly: Remove the rear brake hose and tee joint; Using a small car, support the gearbox housing, remove the 12 bolts connecting the gearbox housing to the rear axle, and remove the gearbox assembly from the axle housing; Disconnect the brake chamber hose and the connection between the pipelines, remove the brake chamber, and remove the adjustment arm assembly; 4. Remove the wheel hub adjustment nut locking plate fastening screw, take out the locking plate, and use a special sleeve to remove the wheel hub adjustment nut; Slightly rotate the wheel hub and brake drum assembly, use a puller to pull the wheel hub outward, and lightly tap on the brake drum to loosen the inner ring of the outer bearing. After the inner ring of the outer bearing is loose, remove the wheel hub and brake drum assembly. However, at this time, be careful not to damage or injure people by falling, and also protect the inner ring of the outer bearing from falling; 5. Use a puller to remove the inner ring assembly of the inner bearing and the oil seal seat ring assembly; Use a return spring disassembly tool to remove the brake return spring and remove the camshaft; Use a wrench to remove the fastening bolts of the brake base plate, remove the brake base plate with shoes and dust cover assembly; Remove the brake chamber bracket and the axle housing assembly; 6. Finally, the reverse order of installation and disassembly is sufficient

Brilliance BMW X1 introduce

The domestically produced Brilliance BMW X1 and the imported version X1 are almost identical. For BMW, there are no missing iconic details. The front face still features the standard dual kidney grille, coupled with the energetic triangular eyes, giving the entire front face a certain aura. The main difference between the domestically produced X1 xDrive20i and 28i on the front face is that they use a black grille while the 28i uses a chrome grille, The 28i has an additional horizontal chrome strip on the lower grille compared to the 20i. On the side of the Brilliance BMW X1, there is not much decoration, and a slightly upturned waistline gives its side a sense of power. The snowflake shaped five spoke aluminum alloy wheels add some fashionable elements to this sense of power, and the two are well integrated. On the C-pillar at the rear of the car, The classic corners of BMW are clearly visible, while the 28i has an additional silver skirt trim on the side compared to the 20i. At the rear, X1 continues to follow the rugged route of an SUV, but what reflects this ruggedness is the few simple lines. The large rear window occupies the majority of the rear. The sharp LED tail lights in the shape allow X1's body lines to continue here. The difference between the 20i and 28i at the rear is not significant, Mainly in terms of the silver trim on the rear bumper, the 28i is taller