Front turn signal introduce

Turn signal is an important indicator light that is activated when a motor vehicle turns to remind the front, rear, left, right, and pedestrians to pay attention. The turn signal tube uses xenon gas tubes, a microcontroller control circuit, and the left and right rotate continuously to flash. The turn signal uses a flasher to achieve light flashing. It can be mainly divided into three types: wire blocking, capacitive, and electronic. Among them, wire blocking can be further divided into hot wire (electric heating) and wing type (bouncing), Electronic flashers can be divided into hybrid (with contact relays and electronic components) and fully electronic (without relays). For example, pop-up flashers use the principle of electric current thermal effect, which uses thermal expansion and contraction as power to cause sudden changes in the spring plate to connect and disconnect the contacts, achieving flashing lights. Turn signals are the most important device that represents the dynamic information of the car, installed in front and behind the body, and can be turned on when the car turns, providing safety assurance for driving, For your and others' safety, please use turn signals according to regulations, so that people can know the direction of the car in advance and make correct judgments)

Installation of front turn signals/rear turn signals/LED daytime running lights/side marker lights/front and rear position lights

Tool preparation: 1. First, we need to prepare the tools required for the entire process of installing car turn signals, including a screwdriver and a wire hook. Then, we need to prepare the car turn signals that need to be installed. 2. Turn on the double flash. As shown in the figure, open the car's key door, and press the switch button of the double flash by hand. This way, the car's double flash will open. Observe the position of the turn signal wire harness. Now we can take out the iron hook, You can make this iron hook yourself, just put it on a wire head. It's quite simple because we have a dual flash, so we can observe the position of the turn signal harness through the hole. 3. Hook out the turn signal. As shown in the figure, after we find the position of the turn signal harness, we use the small iron hook made to hook the harness, and then hook out the turn signal. Be careful to hook it slowly, Avoid disconnecting the wiring harness, and also be careful not to scratch the surface of the car, which may affect its appearance. For the first time installing a car turn signal, as shown in the figure, take out the car turn signal that needs to be installed. Let's take a closer look. There are two small snap holes on the turn signal lampshade that can be directly attached to the turn signal. Please find a good position and gently attach the turn signal to the lampshade. 4. Installation of the car turn signal. As shown in the figure, Gently clip the pre installed car turn signal light onto the card hole on the body of the car, making sure the position of the card is accurate. There is a small iron plate on one side of the turn signal light, so we need to install the plastic side first, and then gently fasten the side with the small iron plate!

Fiat CROMA introduce

The new Croma station wagon has a more dynamic and modern exterior design, although only modified from the current model, the effect is indeed immediate. The new car incorporates the design elements of the new generation Fiat, and we can see the shadow of the new Punto and Brava. The engine hood of the new car has clear lines and a strong sense of power. The elongated front headlights are very dynamic, and the horizontal grille has been replaced by a chrome plated mesh. The tail light shade is darker and cooler than the old model, and the new design of the rear bumper is more dynamic. The cabin of the new car has also been decorated, full of Italian style luxury. The seats are made of leather and fabric. The newly designed instrument panel and steering wheel are very elegant. The standard configuration of the new Croma is already very rich, including rain sensors, reverse radar, tire pressure sensors, cruise control system, ABS anti lock braking system, EBD brake force distribution system, ESP body stability control system, front dual airbags, side airbags, air curtains, and knee airbags. In addition, the new car also has a large number of optional configurations, Including DVD audio and video system, navigation and information system with Bluetooth function, high fidelity audio system, etc. The second row seats can be fully folded, and when the passenger seat is folded down, it becomes a small coffee table. The cargo space can be conveniently increased from 500 liters to 1610 liters. Fiat provides five engines for users to choose from for the new Croma, including two gasoline engines and three Multijet turbocharged diesel engines. The entry-level power is a 1.8-liter gasoline engine with a 140 hp output, and the top-level power configuration is a 2.4-liter turbocharged diesel engine with a 200 hp output. The diesel engine comes standard with a six speed automatic transmission, while the gasoline engine comes standard with a five speed manual transmission. 2.2 A gasoline engine can be equipped with a six speed automatic transmission, while a 1.9-liter diesel engine can be equipped with a five speed manual transmission (Kevin Lee)