rear axle assy introduce

The rear axle refers to a bridge that connects two rear wheels. The rear axle of a rear wheel drive vehicle is called the drive axle, while the rear axle of a non rear wheel drive vehicle is called the support axle. The rear suspension assembly often appears in passenger cars, A component generally composed of springs, shock absorbers, connecting rods, etc., which serves to transmit and support the excitation between the tire and the vehicle body. It is generally divided into three types of independent suspensions (link type), semi independent suspensions (torsion beam type), and non independent suspensions (axle or axle type). The rear axle refers to a bridge that connects two rear wheels. The rear axle of a rear wheel drive vehicle is called the drive axle, and the rear axle of a non rear wheel drive vehicle is called the support axle, The rear suspension assembly refers to the independent suspension system used to support the rear body of a vehicle)

Installation method of rear axle assembly/front axle assembly

1. Unscrew the oil drain plug at the bottom of the axle housing and drain the lubricating oil from the axle housing; Remove the connecting bolts between the flange of the driving bevel gear and the transmission shaft; 2. Disassembly of the half shaft. Before disassembly, cover the front wheels with a wooden cover and release the parking brake. When disassembling, loosen and unscrew all half shaft fastening nuts and washers; Gently strike the center of the rear end of the half shaft 2 to 3 times with a copper hammer to separate the half shaft flange surface from the hub connection surface. Then, pull the half shaft flange by hand to extract the half shaft. Note that when the spline part of the half shaft is about to pass through the oil seal, hold the half shaft rod with your hand and slowly rotate the half shaft to move it out in parallel, so as not to damage the half shaft oil seal and prevent it from falling and injuring people; 3. Disassembly of the main reducer assembly: Remove the rear brake hose and tee joint; Using a small car, support the gearbox housing, remove the 12 bolts connecting the gearbox housing to the rear axle, and remove the gearbox assembly from the axle housing; Disconnect the brake chamber hose and the connection between the pipelines, remove the brake chamber, and remove the adjustment arm assembly; 4. Remove the wheel hub adjustment nut locking plate fastening screw, take out the locking plate, and use a special sleeve to remove the wheel hub adjustment nut; Slightly rotate the wheel hub and brake drum assembly, use a puller to pull the wheel hub outward, and lightly tap on the brake drum to loosen the inner ring of the outer bearing. After the inner ring of the outer bearing is loose, remove the wheel hub and brake drum assembly. However, at this time, be careful not to damage or injure people by falling, and also protect the inner ring of the outer bearing from falling; 5. Use a puller to remove the inner ring assembly of the inner bearing and the oil seal seat ring assembly; Use a return spring disassembly tool to remove the brake return spring and remove the camshaft; Use a wrench to remove the fastening bolts of the brake base plate, remove the brake base plate with shoes and dust cover assembly; Remove the brake chamber bracket and the axle housing assembly; 6. Finally, the reverse order of installation and disassembly is sufficient

Fiat CROMA introduce

The new Croma station wagon has a more dynamic and modern exterior design, although only modified from the current model, the effect is indeed immediate. The new car incorporates the design elements of the new generation Fiat, and we can see the shadow of the new Punto and Brava. The engine hood of the new car has clear lines and a strong sense of power. The elongated front headlights are very dynamic, and the horizontal grille has been replaced by a chrome plated mesh. The tail light shade is darker and cooler than the old model, and the new design of the rear bumper is more dynamic. The cabin of the new car has also been decorated, full of Italian style luxury. The seats are made of leather and fabric. The newly designed instrument panel and steering wheel are very elegant. The standard configuration of the new Croma is already very rich, including rain sensors, reverse radar, tire pressure sensors, cruise control system, ABS anti lock braking system, EBD brake force distribution system, ESP body stability control system, front dual airbags, side airbags, air curtains, and knee airbags. In addition, the new car also has a large number of optional configurations, Including DVD audio and video system, navigation and information system with Bluetooth function, high fidelity audio system, etc. The second row seats can be fully folded, and when the passenger seat is folded down, it becomes a small coffee table. The cargo space can be conveniently increased from 500 liters to 1610 liters. Fiat provides five engines for users to choose from for the new Croma, including two gasoline engines and three Multijet turbocharged diesel engines. The entry-level power is a 1.8-liter gasoline engine with a 140 hp output, and the top-level power configuration is a 2.4-liter turbocharged diesel engine with a 200 hp output. The diesel engine comes standard with a six speed automatic transmission, while the gasoline engine comes standard with a five speed manual transmission. 2.2 A gasoline engine can be equipped with a six speed automatic transmission, while a 1.9-liter diesel engine can be equipped with a five speed manual transmission (Kevin Lee)