The sheep horn of a car is called a "steering knuckle" or "steering knuckle arm", which is the axle head at both ends of the front I-beam that bears the steering function. It is somewhat like a sheep horn, so it is commonly known as a "sheep horn". The steering knuckle, also known as a "sheep horn", is one of the important parts in the steering axle of a car, which can make the car stable and sensitively transmit the direction of travel. The function of the steering knuckle is to transmit and bear the front load of the car, Support and drive the front wheels to rotate around the main pin, causing the car to turn. In the driving state of the car, it bears variable impact loads, so it is required to have high strength. The front axle is equipped with a front axle head on the axle and a steering arm on the seat, just like a sheep horn, so it is called a sheep horn. Generally, it is connected to the front axle by the Liren axle, which is often the case on trucks, Nowadays, cars are all equipped with independent suspensions. Hello, the sheep horn of a car is also known as the steering knuckle assembly. The steering knuckle is one of the main components on the steering axle of a car, which can ensure stable driving and sensitively transmit the direction of travel. The function of the steering knuckle is to bear the load on the front of the car, support and drive the front wheels to rotate around the main pin, and make the car turn. In the driving state of the car, it bears variable impact loads. Therefore, Require it to have high strength. Kingpin inclination angle and front wheel camber angle)
If the car horn needs to be replaced, it is recommended to go to a repair shop for replacement. Generally, it cannot be replaced by oneself, which is quite complex. The function of the car horn is as follows: 1. The role of the car horn is to transmit and bear the front load of the car, support and drive the front wheels to rotate around the main pin, and make the car turn. In the driving state of the car, it bears a variable impact load, so it requires high strength; 2. The sheep horn of a car is called the "steering knuckle" or "steering knuckle arm", which is the axle head at both ends of the front I-beam that bears the steering function. It is somewhat like a sheep horn, so it is commonly known as a "sheep horn"; 3. The steering knuckle, also known as the "steering knuckle", is one of the important components of a car's steering, which can make the car run smoothly, stably, and sensitively transmit the direction of travel. Generally, replacing the steering knuckle requires going to a 4S store. The steering knuckle of a car is called the "steering knuckle" or "steering knuckle arm", which is located on both sides of the front I-beam and bears the steering function of the axle head. It is somewhat like a sheep horn, So it is commonly known as "sheep horn". It is recommended to consult the sales personnel or after-sales technicians of 4S dealerships. If the sheep horn is replaced, the wheels need to be disassembled. If the brake cylinder is replaced, the wheels, brake cylinder, steering rod, support arm, and wheel bearings need to be disassembled. After replacement, four-wheel alignment should be done
The Jaguar XFL was launched in 2016. In terms of exterior design, the domestically produced Jaguar XFL is basically the same as the imported version, with only a significant increase in body length, but the extended wheelbase does not damage the original side profile. In terms of size, the length, width, and height of the Jaguar XFL are 5093/1880/1456mm respectively, with a wheelbase of 3100mm, an increase of 140mm compared to the imported Jaguar XFL. In terms of space, the rear knee space of the domestically produced XFL has increased by 116mm, reaching 203mm, Legroom increased by 157 mm. In terms of power, the Jaguar XFL will be equipped with a 2.0T engine, available in 200Ps and 240Ps high and low power versions, with a 0-100 km/h time of 8.1 seconds and 7.4 seconds respectively. In addition, the new car will also offer a 3.0T V6 turbocharged engine version, with a maximum power of 340 Ps and a 0-100 km/h time of 6.0 seconds
Copyright © 2021.Company name All rights reserved.