Front wheel horn introduce

The sheep horn of a car is called a "steering knuckle" or "steering knuckle arm", which is the axle head at both ends of the front I-beam that bears the steering function. It is somewhat like a sheep horn, so it is commonly known as a "sheep horn". The steering knuckle, also known as a "sheep horn", is one of the important parts in the steering axle of a car, which can make the car stable and sensitively transmit the direction of travel. The function of the steering knuckle is to transmit and bear the front load of the car, Support and drive the front wheels to rotate around the main pin, causing the car to turn. In the driving state of the car, it bears variable impact loads, so it is required to have high strength. The front axle is equipped with a front axle head on the axle and a steering arm on the seat, just like a sheep horn, so it is called a sheep horn. Generally, it is connected to the front axle by the Liren axle, which is often the case on trucks, Nowadays, cars are all equipped with independent suspensions. Hello, the sheep horn of a car is also known as the steering knuckle assembly. The steering knuckle is one of the main components on the steering axle of a car, which can ensure stable driving and sensitively transmit the direction of travel. The function of the steering knuckle is to bear the load on the front of the car, support and drive the front wheels to rotate around the main pin, and make the car turn. In the driving state of the car, it bears variable impact loads. Therefore, Require it to have high strength. Kingpin inclination angle and front wheel camber angle)

Installation steps for front wheel horn/steering knuckle/steering knuckle arm

If the car horn needs to be replaced, it is recommended to go to a repair shop for replacement. Generally, it cannot be replaced by oneself, which is quite complex. The function of the car horn is as follows: 1. The role of the car horn is to transmit and bear the front load of the car, support and drive the front wheels to rotate around the main pin, and make the car turn. In the driving state of the car, it bears a variable impact load, so it requires high strength; 2. The sheep horn of a car is called the "steering knuckle" or "steering knuckle arm", which is the axle head at both ends of the front I-beam that bears the steering function. It is somewhat like a sheep horn, so it is commonly known as a "sheep horn"; 3. The steering knuckle, also known as the "steering knuckle", is one of the important components of a car's steering, which can make the car run smoothly, stably, and sensitively transmit the direction of travel. Generally, replacing the steering knuckle requires going to a 4S store. The steering knuckle of a car is called the "steering knuckle" or "steering knuckle arm", which is located on both sides of the front I-beam and bears the steering function of the axle head. It is somewhat like a sheep horn, So it is commonly known as "sheep horn". It is recommended to consult the sales personnel or after-sales technicians of 4S dealerships. If the sheep horn is replaced, the wheels need to be disassembled. If the brake cylinder is replaced, the wheels, brake cylinder, steering rod, support arm, and wheel bearings need to be disassembled. After replacement, four-wheel alignment should be done

Dongfeng Xiaokang K07 II introduce

The Dongfeng Xiaokang K07 II is a van under the Dongfeng brand. It has been adjusted at the front grille, and the layered lines on the side of the body are more prominent. Compared with the old model, the exterior design of the Dongfeng Xiaokang K07 II has been slightly modified. The front grille has been adjusted, and the layered lines on the side of the body are more prominent. In terms of size, its length has increased by 80mm, The height has been reduced by 40mm. This time, we are introducing the lowest configuration model of the entire series - the 1.0L practical model. The front and rear bumpers of the car are black, priced at 29800 yuan. In terms of space, when a 176cm tall tester sits in the car, the front headroom is two fists, and the rear legroom is also two fists. The headroom is more than two fists, and the slight headroom has never been a problem. In terms of the trunk, its minimum depth is 1110mm, Folding the rear seats can expand to 1940mm, but folding them requires the use of tools, which is somewhat inconvenient. Due to the limited size of the body, the performance of the trunk can only be described as average compared to the other three models